So everything has been going good on the install tell today when I went to put on my intercooler and the hotshot intercooler kit FOR THE BLUEBIRD, NOT THE AVENIR! They sent me the wrong kit, so I could install all of it except the compressor outlet pipe!!! Emailed them today so hopefully I can get it in the next few weeks!!!! I swear if it wasn't for this form I would have had way more trouble!!! I have came here time after time during the install for help. So thanks to all of you. Here's a few pics!!!

http://memimage.cardomain.net/member_images/12/web/384000-384999/384714_25_full.jpg

http://memimage.cardomain.net/member_images/12/web/384000-384999/384714_26_full.jpg

http://memimage.cardomain.net/member_images/12/web/384000-384999/384714_27_full.jpg

Cool, when did you start your swap?

looks great

I have been slowly doing it in october. I had a huge delay cause of the trans I was waiting on. I am converting it to a 5speed also. I got a place in Portland that dose the conversions for $250 labor, so I figure I could do it myself, but cutting the clutch pedal scares me! If anyone wants to make a few extra bucks I'd pay ya to help do the conversion. I am in S.E. Portland. Here's the setup I got going on.

Engine: U12 BB SR20DET engine, Q45 maf, HS intercooler piping w/ XSpower intercooler, Apexi BOV,Weapon R FPR,Greddy Rocker arm stoppers,DEI Cryogenics intercooler sprayer, MSD 6A Ignition W/ Blaster SS coil, 3 inch dp w/ 3 inch carsound cat, with 3 inch Megan catback with carbon fiber muffler, gunmetal powder coated valve cover and heat shields,Greddy oil catch can, in-cabin manual boost controler

Drivetran: LSD 5spd transmission, JWT lightend flywheel, Spec Stage 3 six puck sprung clutch, Short shifter

Gauges: ApexI SAFC II,ApexI Tach, Apexi Boost gauge, Apexi turbo timer, Megan A/F, water, and oil temp gauges.

Rollers: 18' Motegi ff5's w/ nankang tires,Daiyama coilovers, crossdrilled/slotted rotors

Body: Extreame Dimensions R32 front and rear, Pakifier side skirts, carbon fiber hood.


What kinda power you think I will throw down to the wheels? I am planing on boosting 12psi daily. I got a shop who will dyno tune it, so I am guessing around 220whp???

"What kinda power you think I will throw down to the wheels? I am planing on boosting 12psi daily. I got a shop who will dyno tune it, so I am guessing around 220whp???"

sounds about right.
12 for daily driving may be a little high (just MY opinion)
highest ill run my t25 is 10. ive had way too many problems to crank it up any more.

good luck and keep me updated
looks good
bill

What shop did u get ur det from? im in vancouver and looking to swap my freshly swapped 4 door!

I got the engine from Larry Low , he's on the forum, or you can call him at 925 457-3198. If ya need a place that will drop it in, you can call UnNatural Inc. at 503-626-2177, or I can help you out.

I got the engine from Larry Low , he's on the forum, or you can call him at 925 457-3198. If ya need a place that will drop it in, you can call UnNatural Inc. at 503-626-2177, or I can help you out.


im looking to get everything i need, but iw ant it stock, stock ecu, injectors, turbo, TMIC, so stock det ready to bolt up, nothing after market or modded, straihgt bolt in plug in affair!
how much did u pay for ur motor? and can i get a stock de-t with everything i need from this guy?

yeah get ahold of larry, it should cost you about $1300 shipped for a bluebird det

yeah get ahold of larry, it should cost you about $1300 shipped for a bluebird det


for everything i need to be running? and running right?

whats the power gold that u looking for....if any right now

What kind of help do you need on the automatic to manual swap? I have done 2 of them, and I was the one that wrote the article for Nissan Performance Mag, and I am in Camas, WA.

I just need help cutting the hole for the clutch pedal, hooking up the shift linkage, basicly everthing except installing the housing wich I have already done.

Well, if the G20 clutch mounts are the same as the B13, I have a template which makes it easy. Where abouts in Portland are you? I live in Camas, and work in Wilsonville, OR.