|
mpg9999 02-06-2006, 09:49 PM http://static.summitracing.com/global/images/prod/large/prf-70107_w.jpg Any good ideas? It almost fits under the center consol thing in front of the shifter, but it would be pushing down on the wires pretty hard. t bags 02-06-2006, 09:51 PM glove box mpg9999 02-06-2006, 09:52 PM glove box Then I can't put stuff in it, I have to put holes through the dash, and its on the opposite side of where I need to run the wires to. scortch99th 02-06-2006, 09:57 PM what are you using it for ????? johnand 02-06-2006, 09:59 PM what are you using it for ????? X2, and who makes it? mpg9999 02-06-2006, 10:00 PM what are you using it for ????? VVL Solenoids, radar detector, greddy mss, and gauges. johnand 02-07-2006, 10:11 AM VVL Solenoids, radar detector, greddy mss, and gauges. Nice, Painless Wiring makes some nice products. This is what I did, and where I mounted mine: http://www.johnandtracey.com/gallery/albums/nissan_fuseblock/aae.sized.jpg (http://www.johnandtracey.com/gallery/albums/nissan_fuseblock/aae.jpg) Sorry for the crappy picture, that is from my old camera. That is a Blue Sea Systems Fuse Block (http://www.bluesea.com/product.asp?Product_Id=30990&d_Id=7463&l1=7463&l2=#) It is for my alarm, gauges, etc. scortch99th 02-07-2006, 11:25 AM racepartssolutions.com has some fuse blocks like that for cheap prices. chriscar 02-07-2006, 11:29 AM Nice, Painless Wiring makes some nice products. This is what I did, and where I mounted mine: http://www.johnandtracey.com/gallery/albums/nissan_fuseblock/aae.sized.jpg (http://www.johnandtracey.com/gallery/albums/nissan_fuseblock/aae.jpg) Sorry for the crappy picture, that is from my old camera. That is a Blue Sea Systems Fuse Block (http://www.bluesea.com/product.asp?Product_Id=30990&d_Id=7463&l1=7463&l2=#) It is for my alarm, gauges, etc. That's where I was going to suggest he mount it, but I don't know what the dimensions of the one he has. C SERfanatic 02-07-2006, 01:23 PM OT, where did you purchased it from and for how much? Avshi750 02-07-2006, 01:45 PM ~$60 from summit mpg9999 02-07-2006, 02:01 PM Nice, Painless Wiring makes some nice products. This is what I did, and where I mounted mine: Sorry for the crappy picture, that is from my old camera. That is a Blue Sea Systems Fuse Block (http://www.bluesea.com/product.asp?Product_Id=30990&d_Id=7463&l1=7463&l2=#) It is for my alarm, gauges, etc. Like I said I tried to put it there, but its very tight and puts alot of pressure on the wires (they come out of the back of the painless wiring one). johnand 02-07-2006, 04:46 PM Like I said I tried to put it there, but its very tight and puts alot of pressure on the wires (they come out of the back of the painless wiring one). Do you have cruise? If not, the kick panel on the drivers side might work. You could also remove the covers where the ECU is and mount it just in front of the ECU. I have a bank or relays and an ignition controlled fuse block there. Not quite as easy to access though. | ||