Hi guys!!!
i'd like to ask you some questions about sr16ve
1-what is normal compression on this engine?
2-how names the original spark plugs?

PS guys! is anybody of you managed to change brakes (rotors, carriages, wheel hubs...) on PULSAR JN15?

']
1-what is normal compression on this engine?


Looks to be 11.00:1
Here are some stats for a VZ-R (this is the Lucino version but the only difference is trim/lights)

http://www.globalcar.com/datasheet/Nissan/NissanLucinoTwinCam1600VZ-R.htm

Looks to be 11.00:1
Here are some stats for a VZ-R (this is the Lucino version but the only difference is trim/lights)

http://www.globalcar.com/datasheet/Nissan/NissanLucinoTwinCam1600VZ-R.htm

Please don't confuse comression and compression ratio;)
I had asked about comression which is measured by compressor gage:)

Is anybody had checked out the compression ratio on sr16ve?

']Is anybody had checked out the compression ratio on sr16ve?

mine was at 220 on all 4 cylinders. I have changed rotors and pads on my vzr

220 psi? its about 15,5 kg/cm2?

JDM 20ve in a B13 so I'm no help, but I thought it pretty nifty that three guys from WAY far away from the US were the posts so far in this thread. Artem, hope you get the help you need.
Jer

']220 psi? its about 15,5 kg/cm2?

Yes 15.5 kgcm2 is right. What would you like to know about pads and rotors

My Compression was about 16....
The CR is 11.3 in the catalog.

vzrboy, i would like to know if anybody here managed to use rotors, carriages from skyline, z32 etc. (4pot) on pulsar/sentra/nx?

I got Z32(same as R33 calipers) on my Pulsar.

It is not an easy conversion but it is possible. Need atleast 17" rims to clear the calipers and even then, you may need to machine down the Nissan lettering so the spokes clear the calipers.

I would fit NGK brand BKR6EIX-11 spark plugs in a SR16VE.

I got Z32(same as R33 calipers) on my Pulsar.

It is not an easy conversion but it is possible. Need atleast 17" rims to clear the calipers and even then, you may need to machine down the Nissan lettering so the spokes clear the calipers.

I would fit NGK brand BKR6EIX-11 spark plugs in a SR16VE.
Thanks! I has read that its enough to get 16" rims! Did you use adapter to fit the caliper? Have you got photos of this operation?

You will definitely need atleast 17" rims. My 18" rims only just clear as the Pulsar has a different offset to the 300ZX/Skylines. I guess it all depends on what rims you have and how much room there is behind them.

I did not have to use an adaptor but I did have to have some custom brake discs made up to clear the lower control arm.

I am in the middle of doing a major rebuild on my car so will try and get some pics when I am not busy.

You will definitely need atleast 17" rims. My 18" rims only just clear as the Pulsar has a different offset to the 300ZX/Skylines. I guess it all depends on what rims you have and how much room there is behind them.

I did not have to use an adaptor but I did have to have some custom brake discs made up to clear the lower control arm.

I am in the middle of doing a major rebuild on my car so will try and get some pics when I am not busy.
Thank you that you answer my questions-)...How I have understood from your message, a carriage from Z32 will fit on pulsar's native wheel hubs?If there will be problems at installation of a rotor from Z32 besides I should make holes 4*100?

PS How many wheight Z32 carriage? How many weight Z32 rotor? Thanks:)

Guys! don't ignore my posts please :bowdown: ;)

maybe people don't know?

maybe people don't know?
may be:(

:) nobody knows...