: Installing ES rack bushings...
Black200sxSER 04-22-2002, 08:05 PM Hey all..I know I saw awhile back, someone who had a webpage that desribed the process and had pics along with it..even down to trimming out the notch needed....
Does anyone know where this was. I just wanna check it out before I do it in a couple months..(if I can still get em). It had a few tips and tricks I believe.thats kinda what I was looking for.the easiest way to do it. :D If anyone knows the link.please post it.thanks
DubuRX 04-23-2002, 08:03 AM NOPE!!! Not at all... Sorry! Wish I could help you out, but, Naw, I don't have any clue. Maybe...... ummmm.... NO! sorry again...
eric96ser 04-23-2002, 09:55 AM I had that on my web page, but the sr20de.org site is down, and that's where it was. I have a copy of it at home, and I'll email it to you tonight.
98sr20ve 04-23-2002, 10:11 AM Originally posted by eric96ser
I had that on my web page, but the sr20de.org site is down, and that's where it was. I have a copy of it at home, and I'll email it to you tonight.
I am in the same situation. Can you e-mail it to me also.
stevefoltz@hotmail.com. Pleassssse
Steve
SmoothDaddyFig 04-23-2002, 10:21 AM Yeah, eric had it on his site. With good pics too, if you dont me me saying so.
brian 04-23-2002, 11:06 AM oh, and have fun doing the drivers side ;)
Black200sxSER 04-23-2002, 11:13 AM sweet..I knew I saw it on someones page I was looking at..thanks...
eric96ser 04-23-2002, 11:17 AM You just don't have MaD sKilLz Brian
eric96ser 04-23-2002, 07:11 PM Here ya go: steering rack bushings install (http://www.sr20deforum.com/eric/howtos/Steering_Rack/steering_rack_instal.htm)
98sr20ve 04-23-2002, 07:26 PM Would this all be easier to do with the engine out. I am getting a VE and could wait until it goes in.
Steve
Black200sxSER 04-23-2002, 09:49 PM Tight.thank you thats what I was looking for!
Peanuthead 04-23-2002, 10:22 PM How much of a difference does this bushing make?
WhiteSER 05-17-2002, 01:58 PM Is it required to remove the cross member?
eric96ser 05-17-2002, 02:53 PM Not really, but the tranny is very close to the driver's side bracket. If you can lower the tranny a little, it makes it easier. Others have done this without lowering th etranny, and they said it was a big pain. I think it took me about 1 1/2 to 2 hours to install, but this was with fighting with the driver's side bushing. Now that I know about the indention that is needed, I could knock them out in about 1 hour.
WhiteSER 05-17-2002, 02:58 PM Thank you!
Hawaii_SE-R 05-17-2002, 03:02 PM You don't have to remove the tranny, you don't have to remover the cross member, and you don't have to drop the engine. You just need to have long arms to reach the driver's side bushing from the top.
Just remember to remove both bushings and replace them at the same time before you tighten down either of the brackets. This will allow for more movement in the rack so you don't have to struggle too much with wrapping the driver's side bushing into place.
LBCStudios 08-13-2007, 09:59 PM I know I'm bringing this back from the dead.. but I kinda need link.. anyone know where I can find this writeup?
TurboTank 08-14-2007, 08:42 AM im thinking there should be a howto in the howto section, but there isnt. hmm
ES rack how-to! how-to! how-to!!!!!!!!!!
anybody done these lately?
LBCStudios 08-15-2007, 11:08 PM Now that I know about the indention that is needed, I could knock them out in about 1 hour.
Anyone know what he means by this? where this indention goes? :confused:
|