Can one of you guys test this out (preferably someone with an already working version of CalumSult installed)? It should stream the TP and B-cal into LogWorks2/3 if you have that installed too.

Take some datalogs and post them please.

Thanks!

For B13/S13 guys with a Realtime, I'll make a post on how to edit the B13/S13 bins to stream TP and b-cal, until then this will not work with B13/S13 etc ecus.

http://www.calumsult.com/calumsu/CalumSult/CalumSult%20-%20TP%20Beta.exe

anyone?

I posted a modified bin in your thread.

When you first start the new version, stick '07' in both TP Index and Base Fuel Sched (I haven't got base fuel worked out yet for the S13/B13, that may be tricky). Confirm it works and I'll modify it to remember your addresses for each. I'm also adding a map trace function using this.

Let me know that its working and I'll post how to modify the bins to stream TP with normal consult registrs (or any other byte in memory you want to watch). Btw, this streams the MSB of TP, ala Nissan DataScan. We could grab MSB+LSB but I don't think you really need that much precision. I dunno, thoughts? The limitation is you can only stream 20 bytes.

I posted a modified bin in your thread.

When you first start the new version, stick '07' in both TP Index and Base Fuel Sched (I haven't got base fuel worked out yet for the S13/B13, that may be tricky). Confirm it works and I'll modify it to remember your addresses for each. I'm also adding a map trace function using this.

Let me know that its working and I'll post how to modify the bins to stream TP with normal consult registrs (or any other byte in memory you want to watch). Btw, this streams the MSB of TP, ala Nissan DataScan. We could grab MSB+LSB but I don't think you really need that much precision. I dunno, thoughts? The limitation is you can only stream 20 bytes.

I'm not sure what you mean by "stick '07' in both TP index and base fuel sched". Can you give me more instructions?

Sure. Type '07' on the front page. Currently its 33 and 32. Change that to '07' in both cases. Its on the initialize tab, right when you launch the app.

What thats setting is where in the consult register table your pulling data from. For B14/S14s 33 and 32 are valid stock indexes (and are the correct index for TP and B/sched). The B13/S13 ecus consult register table doesn't extend that far, so we're stealing unused spots to stream TP (in this case the spots for the second MAF sensor).

the software dont works on vista

Yea, its made for XP.

You can run it in XP compatibility mode in Vista.

I did a quick check tonight using your updated Calumsult_TP and Logworks2/3. I did not start or drive the car but Logworks brought in the both the TP and Fuel_B variables as RAW. I'll check more tomorrow.

Thanks again, sorry I'm a threadjacker! :)

its working good on my car. http://daj.cz/r/calumLW.jpg
i tried the CalumSult - LW2 Beta.exe

wait you can get consult without real time on the b14 ecu? Wow I wish I would've known that before :/

Does this allow the use of Logworks for monitoring the engine in real time? Or is it just reading the logs?

I've got Logworks 3, a Consult adapter, and an Avenir ECU.
What do I need to do?

Yep, it streams the data into logworks. Open and connect calumsult first, turn on the gauges, then start logworks. To use the TP version on B13/S13s you need to modify the bin. It will work with no modification on the B14/S14 ecus.