I'm a long time reader of this forum, but i havnt had anything but my daily driver to work with before. I just bought a '95 200sx SE and im interested in putting a VE in it. I know that ill need a Tranny/RPM Switches/JWT ECU, im shooting for the 01 Tranny because im already used to the gearing. My question to all of you is what else am i going to need to pull this off, since im going from the 1.6DE to a 2.0VE.

I love the support u guys offer each other on this forum.

I know you can add header and axles to the list. I don't know which ones. Unless it is a pure drag car I would upgrade the brakes as well. I would do a search and see what you found for GA16+swap and look for the swap info. Adding the VE is not going to be any harder with the exception of the RPM switchs and that not a big deal.

you'll also need a 2.0 wiring harness and i am not sure about the b-14's but on the b-13's when going to 1.6 to 2.0 you have to change to dog-bone front motor mount. you can just use the oem 2.0 axles. and probably a couple of other little thing i can't remember.
Walter, from N. Cal

so i guess for the "little things":D its just go about the install, and as things are needed buy them. So does anyone know of a place i can find the differences between the 1.6L b14 and the 2.0L b14. That way i can figure out what i need to get before hand, so my swap doesnt take me a week or two? I assumed someone had done swap in a b14 that was non SR20 before.

I havnt ordered the engine yet, but i do have enough money to buy some of the parts. Can anyone help me out thats done a 1.6 to 2.0 swap before... im going to try to make a list so i can order this stuff direct from the dealer wholesale.

Originally posted by jaycue01
Can anyone help me out thats done a 1.6 to 2.0 swap before... im going to try to make a list so i can order this stuff direct from the dealer wholesale.

Have you done a search yet. If not then do that first. If you still have questions post in the general section to get more traffic in your post. The VE swap info I/we can help with but the 1.6-2.0 is not up my alley and is not really specific to the VE section. It shouldn't be any harder to swap a VE into your car then a DE except for the RPM triggers.

i did a search and havnt found anything concrete. I'll try and spread my questions across the general section and here as i go along. Thanxs for the help so far, ill get back to you guys as soon as i get a list of things i need to put in my car. Searching the sight didnt give me much info on a swap from 1.6 to 2.0, but i did find a bit on SE-R.com, so ill let you know how it goes. As far as i can assume once the car is DE ready it should be just like pulling a SR20DE and putting in a VE. Until then thanx for your help.

Originally posted by jaycue01
i did a search and havnt found anything concrete. I'll try and spread my questions across the general section and here as i go along. Thanxs for the help so far, ill get back to you guys as soon as i get a list of things i need to put in my car. Searching the sight didnt give me much info on a swap from 1.6 to 2.0, but i did find a bit on SE-R.com, so ill let you know how it goes. As far as i can assume once the car is DE ready it should be just like pulling a SR20DE and putting in a VE. Until then thanx for your help.

I am not trying to put you off just trying to send you in the right places to get the info you are looking for. I would post the list of stuff you "think" you need for the swap in the general forum and that way you show you have done your homework. I bet you will get a good response to a post that shows that you have done some research already. Good luck.

I don't think an '01 tranny will fit in your car, stick with a 95-97 SE-R/G20 tranny, you know it will fit... Good luck and do ALOT of research...

thanx for the input... ill let you guys know how it goes... at this rate it looks like it might take a few months to complete.

go to nissanperformancemagazine.com
and search there

O