shelnut
01-27-2009, 08:37 AM
1996 Nissan 240SX
5 lug with rb25det The car has working windshield wipers power steering and cold a/c. The harness was professionally done and looks 100% factory.
Suspension/ Brakes:
Peak Performance extended wheel studs
agency power stainless brake lines front and rear
300zx brakes front and rear
k sport hydraulic hand brake
spl tension arms
spl toe arms
spl traction arms
cusco rucas
spl solid aluminum subframe bushings
spl solid aluminum diff bushings
nismo steering rack bushings
spl steering angle spacers
300zx tie rods
spl tie rod ends for 300zx tie rods
k sport coilovers
Engine/Drivetrain:
Rb25det series 2
front mount intercooler (eBay)
top hat engine mounts Welded to subframe
replaced top hats crappy rubber mounts with solid aluminum ones
One piece aluminum drive shaft from the drive shaft shop
spec stage 4 6 puck clutch
greddy profec b spec 2 boost controller
mines tune ecu for factory injectors and turbo
top hat downpipe
J30 lsd diff
Interior:
MoMo steering wheel
Greddy boost gauge
And the rest if factory but super clean
***No Carpet***
Front floor mats
SE Gauge Cluster
Odessey dry cell battery relocated to trunk
Body:
JDM head lights and corner lights
Version select version 1 aero
Could use a paint job and some body work
Wheels/Tires
Tenzo-R DC-6 18x9.5 +15
New Bfgoodrich GForce Sport 225/45 Front
New Nexen N3000 245/40 Rear
The Bad:
I think it needs valve seals. It is smoking and blowing a bit of oil out of the breather hose on the valve cover
The trans grinds at high rpms. Internals are the same 300zx except for the shafts so it shouldn't be too hard to find parts to fix it.
I drive the car everyday and never have any problems.
Price: Throw me offers Kinda looking to get into an SE-R
Price Drop 6500obo
Email: TNracer87@yahoo.com
Location: Johnson City, TN
This is kinda of testing waters but I dont really have the time money or place to work on it. I would consider some trades
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8747-1.jpg
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8745.jpg
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8746.jpg
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8762.jpg
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8760.jpg
5 lug with rb25det The car has working windshield wipers power steering and cold a/c. The harness was professionally done and looks 100% factory.
Suspension/ Brakes:
Peak Performance extended wheel studs
agency power stainless brake lines front and rear
300zx brakes front and rear
k sport hydraulic hand brake
spl tension arms
spl toe arms
spl traction arms
cusco rucas
spl solid aluminum subframe bushings
spl solid aluminum diff bushings
nismo steering rack bushings
spl steering angle spacers
300zx tie rods
spl tie rod ends for 300zx tie rods
k sport coilovers
Engine/Drivetrain:
Rb25det series 2
front mount intercooler (eBay)
top hat engine mounts Welded to subframe
replaced top hats crappy rubber mounts with solid aluminum ones
One piece aluminum drive shaft from the drive shaft shop
spec stage 4 6 puck clutch
greddy profec b spec 2 boost controller
mines tune ecu for factory injectors and turbo
top hat downpipe
J30 lsd diff
Interior:
MoMo steering wheel
Greddy boost gauge
And the rest if factory but super clean
***No Carpet***
Front floor mats
SE Gauge Cluster
Odessey dry cell battery relocated to trunk
Body:
JDM head lights and corner lights
Version select version 1 aero
Could use a paint job and some body work
Wheels/Tires
Tenzo-R DC-6 18x9.5 +15
New Bfgoodrich GForce Sport 225/45 Front
New Nexen N3000 245/40 Rear
The Bad:
I think it needs valve seals. It is smoking and blowing a bit of oil out of the breather hose on the valve cover
The trans grinds at high rpms. Internals are the same 300zx except for the shafts so it shouldn't be too hard to find parts to fix it.
I drive the car everyday and never have any problems.
Price: Throw me offers Kinda looking to get into an SE-R
Price Drop 6500obo
Email: TNracer87@yahoo.com
Location: Johnson City, TN
This is kinda of testing waters but I dont really have the time money or place to work on it. I would consider some trades
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8747-1.jpg
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8745.jpg
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8746.jpg
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8762.jpg
http://i200.photobucket.com/albums/aa236/Shelnut240sx/HPIM8760.jpg