Currently as the car sits it has everything listed below. The W10 has a fast oil leak so I have stopped driving it and has been sitting for the past month with no oil in it as I have prepped it for removal. I have the harness and turbo removed because I was going to pull the engine, swap in my new one and sell it but no longer have the money to complete the built swap. The car does run how it sits but I would not recommend driving it without either fixing the leak (I don't know where its coming from) or swapping in the built engine. I have a fully built engine ready to swap in that has never been run. I also have 4 brand new Falken (205/50/15) tires (0 miles on them) and NEW AXLES and a BRAND NEW Clutchmasters street disc and pressure plate. Kelly Blue Book says the car with stock engine is worth $4200. + Built Engine ($2000 in parts and machine work), W10 Avenier (worth around $800 new)and all the brand new stuff that is included. I will NOT part out the car.

Prices
EVERYTHING I have B14, W10 Avenier w/ B14 Tranny and Fully Built Highport SR20 NEVER RUN! $3000

Call Kevin 321-917-1259 for any questions. I will deliver as far as Jacksonville or Miami for $250.

The Built Engine:

Highport SR20
Block tapped and dripped for oil return
9.1:1 Weisco Pistons
Eagle Rods
ARP Rod Bolts
Block Bored and Honed to .020 86.5mm
Multi-angle Valve Job
Engine Balanced
ALL Work has been performed by a machine shop
The engine has never been started and the engine sits fully assembled.


1996 White Nissan 200sx SE-R

Non smoker
Clean inside and out
209k miles on chassis
15% Tint all around
'98 Honey Comb Grille
Has Ice Cold AC and Power Steering (I just had to pull an AC line...needs a charge)

Engine:
60-90k miles on SR20DET W10 Avenir Engine
T25 Turbo w/ 3" Turbo Back to a Magnaflow exhaust
Greddy Type RS BOV
NEW KOYO RADIATOR
ALL NEW SILICONE COUPLERS FOR INTEROCOOLER PIPING & T-BOLT CLAMPS
Intercooler Piping is 2.25" hot side and 2.5" cold side
370CC Injectors
Fuel Pressure set to 4 BAR
Calum Realtime ECU
Full Prothane Motor mounts
Short Shifter
ES shifter bushings
Custom Steel shifter stabilizer bracket
Fidanza 8.5 flywheel
N60 MAF
Act Heavy Duty PP w/ ACT 6 puck unsprung disc
Clutch cable recently replaced
New Ball Joints, Front Wheel Bearings, Inner And Outer Tie Rods Ends

Suspension:
Ksport Fully adjustable coils
Progress rear sway bar
Octotat Rear strut tower bar

Electronics:
Pioneer Head unit
Pioneer 3 way speakers up front
Pioneer 4 way speakers in the rear

http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture012-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture013-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture014-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture001-3.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture017-2.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture018-2.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture019-2.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture020-2.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture011-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture010-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture009-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture008-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture007-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture006-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture005-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture004-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture003-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture002-4.jpg
http://i488.photobucket.com/albums/rr248/pineapplepalms1259/Picture001-4.jpg

how much would you sell it for, with the built engine installed?

how much would you sell it for, with the built engine installed?

I would ask $6k but i would need an oil feed line, water lines and a few gaskets. I just don't have anymore money.

would you do 2,500 down and the rest in payments

**** sell the b14 wheels? lmk

bump

ttt...EVERYTHING for $4000!

you still have the second engine???

ttt... price drop please buy

bump for a great deal

bump