I’m parting out my current setup and going with something completely different. This is my fully built SR20DET with only 1100 easy break in miles. Motor has never seen boost and has solid 160psi compression and 2% leak down across all 4 cylinders. Motor is built for 600 whp! Here’s the build list and everything included:

Aftermarket parts
S13 redtop motor
Apexi cylinder sleeves
Crower rods (not Brian Crower)
CP 87mm pistons 8.5 compression
ARP main studs
ARP head studs
Greddy oil pan
Cometic MLS head gasket
Comp Cams valve springs
HKS 272 step 2 cams
Greddy rocker arm stoppers
MMR polyurethane motor mounts
ACT 6 puck clutch kit

New OEM parts
Main bearings
Rod bearings
Thrust bearings
Front cover/oil pump and front main seal
Water pump
Timing chain and crank gear
Updated timing chain guides
Timing chain tensioner
Rear main seal
Valve stem seals
Water temp sensor

Machine Work
Balance/polish crank
Balance rotating assembly
Sleeve install/bore/hone
Align hone mains
Decked block and head
5 angle valve job

Other accessories and items included
CAS
Alternator
Starter
Coil packs
Power steering pump with DOHC s13 reservoir
Autometer oil temp sender in oil pan
Coolant temp cluster gauge sender removed and tapped for Autometer 1/8 npt sender
Stock oil pressure sender removed and has Autometer 1/8 bspt ->1/8npt fitting
Heater hose hard lines have nipples removed and welded shut
Stock PCV removed and -10AN fitting has been welded to valve cover for crankcase evac

$4000 plus shipping

Please PM or email at avery_morse@yahoo.com if interested or for any questions.

http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/sleeves.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/PISTONKIT2.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/crowerrods.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor002.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor003.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor005.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor006.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor004.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor008.jpg
http://i18.photobucket.com/albums/b148/avery240sx/car%20stuff/motor014.jpg

How much for your arp HEAD STUDS ?

and is your gasket still good ?

How much for your arp HEAD STUDS ?

and is your gasket still good ?

sorry, not parting it out

anyone interested?

giving you a bump for building it right, glws

price drop $3800 plus shipping

price drop $3800 plus shipping


hey j/w is this the engine that my t67 is off of? lol

btw i had a q about the t67 why trim the intake wheel? arent you supposed to trim the exhaust?

and bump for a legit, quick shipping no bs seller.

hey j/w is this the engine that my t67 is off of? lol

btw i had a q about the t67 why trim the intake wheel? arent you supposed to trim the exhaust?

and bump for a legit, quick shipping no bs seller.

yes, this is the motor the turbo was on. i'll pm you about the turbo. thanks for the bump

any reasonable offers??

open to any offers guys or i'll hold onto this for a while

forgot to mention, i have all the receipts for the parts and machine work.

sale pending