i have a few parts trying get sell to fund a new project or sell the whole motor.spent about 3 grand getting it built looking to get about 750 obo as a whole everything is new in engine car was run one time after build and jump timing.Also have Z32 MAF Blitz BOV alternater and power steering pump. Also have S13 body with a few goodies Nice radiator,Big FMIC,Blitz turbo timer,J30 rear end AVCR controller Chipped ECU and a few other things car is set up for drifting.will sell body and engine together for 2000 bucks your getting a great deal all the expensive stuff is pretty much done willing to trade for a 90 to 95 Z32 5speed doesnt have to be running but has to be in good shape or close to running
cp pistons 87.5
titanium springs and retainers
5 angle valve job
new stock valves
264 cams
rocker arm stoppers
eagle rods
thermal tek intake gasket
greddy oil pan(internally baffeled)
arp head studs
JGY customs pulleys
any questions shoot me a email at iammr3000@yahoo.com or call or text me @ 803 565 7014
http://i789.photobucket.com/albums/yy177/mr3staks/IMG_0213.jpg
http://i789.photobucket.com/albums/yy177/mr3staks/IMG_0246.jpg
http://i789.photobucket.com/albums/yy177/mr3staks/IMG_0242.jpg
http://i789.photobucket.com/albums/yy177/mr3staks/IMG_0227.jpg
http://i789.photobucket.com/albums/yy177/mr3staks/IMG_0221.jpg
http://i789.photobucket.com/albums/yy177/mr3staks/IMG_0228.jpg
http://i789.photobucket.com/albums/yy177/mr3staks/IMG_0229.jpg

how much for fmic and avcr?

how much for the cams z32maf and the apexi shipped to 25705

when i bought the cams, greddy pan, avcr, safc, and z32 maf, he said the avcr came with everything and the cams were "new never been installed"

here is a laundry list of issues:
cams-supposed to be for s13 blacktop, got i (horribly mangled) exhaust cam for an s13 det and 1 shiny new intake cam fo a s14 vvt det! (looks to have been installed but only run for a very short while, as in minuets or hours)

avcr is missing the MAP sensor.
he packaged the cams and oil pan in a box twice as big as it needed to be(not a problem but...) and then he "packaged" them by wrapping one old t-shirt around the cams, and one around the oil pan. seriously wtf, not even newspaper to keep them from shifting around, the oilpan got dented by the cams around where the seal goes so no idea what I'm going to do to repair that, machine shop maybe? lot's of hondabond?

anyway contacted the seller, he said he would buy back the cams from me for $200, was nice about it (over the phone) but then a couple weeks later when i hadn't received anything or heard from him i filed a pay pal claim, and he finally got back to me saying his wife just had surgery and is going into another one and blah blah blah... maybe it's true maybe it's not, doesn't matter. what i do know is that the last time i got screwed the guy did the same exact thing, stopped contacting me, and then started going on about the hurricane and etc...

so for now i have to assume that this guy is scamming me. there is NO WAY he could have thought that that cam was usable, if needed i'll upload pics, there is a 2mm deep channel gouged out around the center bearing race(journal race?) and it's all rusty on the cam lobes like it was sitting outside for a couple of months.

ps, the greddy oil pan had a ton of what looked like copper flakes in it, i'm assuming they are bearing shavings, hope they aren't from the motor he's selling and that that guy that bought it got a decent motor, but looking at the camshaft it's hard not to put two and two together....that many shavings and some were bound to make it to the head.