does anyone know how I can make mine shorter. or buy a new one. (I feel like I am shifting a truck) I just want it about an inch or inch and and a half physical shorter.

thanks guys

sorry about that spelling error.

take off the knob, and take a saw type deal. If you are putting on a new shift knob then just cut away, because they give you new things in there to tighten it up on the shifter. As for you shiter to be shorter, I dont know. Cut off the top part of the toilet and shit in a pipe! Good luck with the shifter.

------------------
Mark Merliss
97 SR20 SE-R(Pacific sun blue)
Its from america's dairyland, what can get any better than that.
Pics up soon!!!

You say you feel like you're driving a truck. Is that because the throws are too long or because the shifter is too tall? I ask because I used to think the NX shifter was too tall, but I have realized that it is not. It is actually in the right place. In my miata, the shifter is shorter, but you also sit lower in that car. Compared to my NX, the shifter is actually in about the same position relative to the driver position.

I put a Pacesetter short shifter kit in and the throws are short and it shifts great! I would recommend you do the same.

Ben
'93 NX

As for you shiter to be shorter, I dont know. Cut off the top part of the toilet and shit in a pipe! Good luck with the shifter.


that you for that one. hahaha. dumb sticky keyboard.

i cant get my damn shift knob off

LOL...hardly anyone ever can get that sucker off!! http://www.plauder-smilies.de/brakelamp.gif

------------------
White
92 Nx2000
Cone intake, 19* timing, bosal performance muffler, 2.25" custom cat-back

I had my stock shifter cut about an inch and half about five years ago. After the shop cut it, they rethread the shaft and put the stock shifter know back on. I have had no problems whatsoever, and of course, shifts are slightly quicker.

I'm not endorsing/suggesting this method (legal crap), but for me, at the time, this was a much cheaper alternative to a short shifter kit. I'm glad I did it. http://www.sr20deforum.com/NonCGI/smile.gif

I took a roto zip to mine and cut about two inches off of it, and put a universal shifter knob on it,works fine for now and I like the way it feels alot better.

------------------
1991 NX2000 W/SR20DET SWAP,HKS filter,3" EXHUAST,E.S. BUSHINGS, act clutch, blitz turbo timer, boost controller

NX 1600 INTAKE,AND EXHUAST

what is a roto zip?

If you install the Pace Setter Short Throw Shifter (>$100) and set the ball as high as possible you will not only get the shortest throws (I LOVE short throws) but you'll also get a SHORTER shifter. The possible downsides are if you don't like short throws and clearance issues with your cat heat sheild. The heat shield issues are easily resolved. You can bend or cut the shield no sweat.

see

http://65.11.246.68/stocker/stockermodsjune00.html

what's the password to see the video?

------------------
Nissan Nx2000 1992 - no cat,
timing advanced to about 18-19 and
15.75@90.8mph(G-Tech...)

reload the page on your browser

it should work without a password

geocities kicked me off so its hosted by my own machine now

don't forget to check out the 2nd video

Bubba - I assume yer using cable internet - you can register a domain name CHEAP (godaddy.com) and then use a free service called DNS2go (dns2go.com) that will point your IP (even if it changes) to your domain on your PC - I use it www.chrisstorer.com (http://www.chrisstorer.com)
Later
Chris

Cool Deal

Thanks Maui

I'll look into it