hmmm $50, no thanks :/

would like to get a rangi CAI made up first.

oooh yeah that reminds me...Shaun, those Samco bends and 4 x hose clips for the CAI are all yours! I'll take them out of the add, I'll give you a call, then you can harass Aaron for the tubing.

sweet, is someone doing a CAI? hopefully if there is a meet up sometime again, i can check some different styles out.

im always keen to meet up with fellow nissan owners silver te, and dan when you buy a house you will have to look at where all the nissan and other car freaks are, mostly out west i reakon.
And i think ill go re dyno this sat, hopefully get more than the 88kw i got last time with only minor serviceing basically.

actually no need for the samco hose and stuff now sorry dan, I am doing something different now, , i think you know what im talking about

I got 107kw atw at the last torque performance dyno day. Just have the usually intake, exhaust and and factory moded headers

yeh ditto here, always kean for a meet up!

I know have two 3" bends sitting here you guys!! :rolleyes: :)

hey Pharnos, did you get my PM on the pulsar forum ages ago?
I've finally got a couple of pics on the intake and catch can if you're interested.....

Catchya all around
nismotoy.

nismotoy - fire them over to pharnos@ihug.co.nz

and as for a little meet or something...how about this sunday morning at bastion point? 10am...auck dudes keen?

Originally posted by nismotoy

I know have two 3" bends sitting here you guys!! :rolleyes: :)


Sorry Mr Aaron..but I will go a head with the filter now then!...one last horrah before she goes!...I'll just get one of the cheap filters I was talking about.

Hey Pharnos, will do, took the disk the pics where on to work and forgot it....typical!

will send them your way tomorrow night :)

not sure about this sunday, probably up north working on the car ;) but that can change!

Should definitely have a combined meet after Autosalon though
get as many guys off the Pulsar forums along as well!!

for those unaware refer: http://www.sr20deforum.com/showthread.php?s=&threadid=43222
& http://forum.pulsar.org.au/showthread.php?s=&threadid=10605

cheers, nismotoy.

ok, ignore this sunday then, and we'll arrange something for after autosalon, sorted

Originally posted by Pharnos
ok, ignore this sunday then, and we'll arrange something for after autosalon, sorted

I cant wait! :D

anyone got any newer info on the autechs? I know this thread was dead but I am still searching for info that anyone may have saved off the autech site before they updated and dropped the N15 from their listings. Plus, babelfish hates the autech site because its mostly flash now [rolls eyes]

I'm really keen on finding more of the info the autech technicians would have used for servicing. Obviously the specs and tolerances will be quite different to those used on standard SR20's



and Shortz, how long before you move to Australia?

Mate...Autech in Japan is the only place you are going to get that kind of info, you might just have to email them...this is as good as you'll get really.
It's for a P10 Primera but it's the same engine/era:

Got an email back from the guys at Autech. Here is what they had to say about the Autech P10:

Changes for the P10 Autech version is as follows:
exclusive exhaust system
exclusive E.C.U.
compression ratio
valve timing
exclusive use suspension
etc.

SPECIFICATIONS Premera Autech version
Exterior Dimensions
Overall height 4400mm
Overall width 1695mm
Overall length 1385mm
Wheel base 2550mm
Weights 1190kg
Engine
2.0liter DOHC 16-vaive 4-cylinder
180ps/6800rpm
19.6kgm/5600rpm
Transmission
5-speed manual
Suspension
front Independent multi-link
rear Independent parallel-link strut
Tires
205/50R15 tires
on 15" 5-spoke aluminum alloy wheels

I pinched that from THIS (http://www.automotivehelper.com/topic2230.htm) site

Thanks Dan... I'll bite the bullet and get SiqRik to help me phone them, his Japanese is far better than mine [nods and laughs] Rick isnt keen on watching pulsar mods now since his was written off but I think he'll be up for helping out on this one.

btw, must organise a cruise early November (in the middle of my honeymoon - mwaahahahaha) Auckland... obviously I wont have my car there but will want to ride with the crew... my fiance is worried the Welly boys will kidnap me for a bucks night... hehe dont tel Sammy!
talk to you soon dude ;)

yeah dude not a problem...let me know how you get on!