SR20 Forum banner

Status
Not open for further replies.
1 - 20 of 22 Posts

·
Registered
Joined
·
521 Posts
Discussion Starter #1 (Edited)
I'M SELLING THE GTIR ENGINE OUT OF MY CAR (GOT HIT FROM BEHIND INSURANCE IS GOING TO TOTAL IT OUT AND WON'T PAY FOR THE MODIFICATIONS SO I'M TAKING THEM.) ANYWAYS IT IS FULLY BUILT ENGINE WITH CROWER RODS, AND WEISCO PISTONS 9:1 COMP BORED 10 OVER STOCK, PORTED AND POLISHED HEAD,50# INJECTORS, COBRA MAF, FMIC w/PIPING, JUN LINGHTED FLY WHEEL, AND ACT XTREME PRESSURE PLATE AND HEAVY DUTY CLUTCH. ENGINE HAS 400 MILES ON IT ASKING $4,500 HAVE WELL OVER THAT INVESTED IN PARTS AND LABOR

ALSO SELLING:
JWT ECU B13-TURBO,COBRA MAF,50# INJECTOR
SPARCO STEERING WHEEL
BLITZ DUAL BOOST CONTROLER
BLITZ T.T./BOOST GUAGE
BLITZ B.O.V. NEVER INSTALLED STILL IN BOX
PROGRESSIVE SWAY BARS FRONT AND REAR FOR 91-94 NX2000
LOWERING SPRINGS FOR 91-94 NX2000
REAER STRUT TOWER BAR 91-94 NX2000
NX WET KIT
NX INTERCOOLER KIT
 

·
merely a flesh wound
Joined
·
15,281 Posts
PM'd.

C
 

·
Registered
Joined
·
880 Posts
what kind of turbo were you runing because if it was a t3/t04e I want those ic pipes.
 

·
Registered
Joined
·
521 Posts
Discussion Starter #9
the engine doesn't have an iron sleeve or anything but the I had it put back together with crower rods, and weisco pistons, clevite bearings. the head was was rebuilt, has a multi angle valve job, and has been ported and polished, with a bench flowing device.
 

·
Registered
Joined
·
521 Posts
Discussion Starter #10
asking $4,000 plus shipping for engine this includes: fully built block (built with crower rods, and weisco pistons 9:1, clevite bearings), ported and polished head, and multi angle valve job,50# injectors, cobra maf, FMIC kit, jun lightend flywheel, ACT xtreme clutch set up, all the sensors, pumps, belts, wires all intact not cut the full engine right out of my car.


JWT ECU B13-TURBO,COBRA MAF,50# INJECTOR asking $300

SPARCO STEERING WHEEL mugello asking $150 incudes hub adapter

BLITZ DUAL sbc asking $150

BLITZ T.T. asking $50

BLITZ B.O.V. NEVER INSTALLED STILL IN BOX asking $150

PROGRESSIVE SWAY BARS FRONT AND REAR FOR b13 asking $250

b&g LOWERING SPRINGS FOR b13 aksing $60
moti REAER STRUT TOWER BAR 91-94 NX2000 asking $75
Nitrous Express WET KIT asking $225
Nitrous Express INTERCOOLER KIT $175

any quetions just p.m. me
 

·
Registered
Joined
·
880 Posts
Hey how much for those sway bars?
 

·
Registered
Joined
·
521 Posts
Discussion Starter #14
I want to $250 for both swaybars, and i'll sell the tranny if you want it but it has reverse pop out
 

·
Registered
Joined
·
521 Posts
Discussion Starter #19 (Edited)
tt bov and boost controler, and rear strut tower bars bar holding for rob

nitrous express wet kit holding for PoorLiLpoop
 
1 - 20 of 22 Posts
Status
Not open for further replies.
Top